May 18, 2005 · You can use the route command to view, add and delete routes on a Microsoft Windows NT server that runs Cisco ICM. You can use these options with the route command: route [-f] [-p] [command [destination] [mask subnetmask] [gateway] [metric costmetric]]
Sep 01, 2009 · This is a video on two common uses of the command route. Route allows you to see your computers routing table. commands used route print route add 10.0.0.0 mask 255.0.0.0 192.168.0.110 Dec 09, 2011 · The process is very simple in Windows 7, however, as all commands the syntax has to be accurate before the command works. You can also choose in Windows to either add the route temporarily or make the route permanent or persistent meaning that it will persist between Windows reboots. The example below show step by step to add persistent route or some say permanent static route on the Windows XP computer, the same rules or command can be apply on Windows 2000 1. Click on Start menu, then click on Run to open the run command window. The correct syntax for route delete is as follows: C:>route delete 192.168.6.0. You would do this if you wanted to undo the changes you made in the example above. route change. The route change command can be used very similarly to the route add command for an existing route. Apr 02, 2013 · I am connected to wireless network in my city. The problem is that when I want to connect to city wireless I need to add a route in Command prompt. In XP it works fine, but when I type this in Vista: route -p add 10.0.0.0 mask 255.0.0.0 10.46.2.1. I recive this message: The requested operation requires elevation. As with the Unix,Linux and Solaris operating Systems, the route command can be used to add static routes in Windows. This should work on Windows 2000,XP,2003. To view the existing routes, C:\> route print. To add a static route, Syntax: C:\> route add
If this is used in conjunction with one of the commands (such as add, change, or delete), the table is cleared prior to running the command. /p. When used with the add command, the specified route is added to the registry and is used to initialize the IP routing table whenever the TCP/IP protocol is started. By default, added routes are not preserved when the TCP/IP protocol is started. When used with the print command, the list of persistent routes is displayed.
The command-syntax is: route [-f] [-p] [-4|-6] [Command [Destination] [mask Netmask] [Gateway] metric Metric if Interface Parameters-f: Clears the routing table-p: The route is added to the Windows Registry and is used to initialize the IP routing table whenever the TCP/IP protocol is started (only when used with the add command) The syntax for the route command for adding, deleting, or changing a route entry is. route [-p] command dest [mask subnet] gateway [-if interface] The following list describes each of the route command’s parameters: –p: Makes the entry persistent. If you omit -p, the entry will be deleted the next time you reboot. (Use this only with add However, I would prefer to add the static routes by specifying a network interface, instead of by specifying a gateway IP address. This is possible with Linux by using a command such as: ip route add 203.0.113.9 dev eth0 and similarly in FreeBSD: route add 203.0.113.9/32 -iface fxp0 -cloning However, I'm at a loss of how to do this with Windows.
Jul 03, 2017 · Add a Static Route to the Windows Routing Table. To add a static route to the table, you’ll type a command using the following syntax: route ADD destination_network MASK subnet_mask gateway_ip metric_cost. The subnet_mask and metric_cost components are optional to the command.
Press the Windows + R key to open the Execute dialog box. We write cmd, followed by Enter to open a DOS window. In the command prompt window, type netsh, and then press ENTER. Type ipv6 interface, and then press ENTER. Static routes can be configured in one of two ways: Using the route command. Using the RRAS management console. Using the Route Command. The route command is used to view and modify the network routing tables of an IP network. The route print command displays a list of current routes that the host knows (see Figure 5.1). If this is used in conjunction with one of the commands, the tables are cleared prior to running the command. destination_host The address (or set of addresses) that you want to reach. -p Create a persistent route - survives system reboots.